Honeywell AUTOMATIC VENT DAMPER D896 Manual do Utilizador descarregar pdf

PRODUCT DATA

® U.S. Registered Trademark

D896 Automatic Vent Damper

GENERAL

D896 Automatic Vent Dampers are used with atmospheric

type, gas-fired equipment to reduce home heating losses by

closing off the vent between heat cycles.

FEATURES

• 4-wire plug receptacle.

• Includes wiring harness on select models to fit plug

receptacle onto S86/S8600/S8610/S8620 /L7148/L8148

or Penn Baso G60 or G66.

• For use only on atmospheric type gas-fired furnaces

and boilers equipped with draft hoods.

• Applicable to direct spark ignition (DSI), intermittent

pilot (IP), hot surface ignition (HSI), and standing pilot

systems.

• Ambient temperature range 32°F (0°C) to 150°F (65°C).

• Requires dual automatic combination gas control

valve or two separate single function main gas valves.

• Interlock switch provides safe operation; burner fires

only with damper in open position.

• 24V operation for easy, low-cost wiring.

• Visual indicator shows damper position.

• 30-second nominal closing time for optimum energy

savings.

• Quiet motor and relay.

• Wiring harnesses available separately to fit a variety of

applications.

68-0186

Contents

General ............................................................................... 1

Features .............................................................................. 1

Specifications ...................................................................... 2

Ordering Information ........................................................... 2

Application........................................................................... 3

Installation ........................................................................... 4

Settings ............................................................................... 7

Operation and Checkout ..................................................... 7

Troubleshooting ................................................................... 8

Instructions to the Homeowner ........................................... 9

ANSI Standards .................................................................. 10

1 2 3 4 5 6 ... 11 12

Resumo do Conteúdo

Página 1 - D896 Automatic Vent Damper

Página 2 - SPECIFICATIONS

D896 AUTOMATIC VENT DAMPER68-018610ANSI STANDARDSEXHIBIT AProcedure For Safety Inspection of an Existing Appliance InstallationThe following procedure

Página 3 - APPLICATION

D896 AUTOMATIC VENT DAMPER68-018611EXHIBIT BProcedure for Installing Electrically Operated Automatic Vent Damper Devices on Existing AppliancesThis pr

Página 4 - INSTALLATION

D896 AUTOMATIC VENT DAMPER68-018612Honeywell Europe S.A.3 Avenue du BourgetB-1140 Brussels BelgiumHoneywell Asia Pacific Inc.Room 3213-3225Sun Hung Ka

Página 5

D896 AUTOMATIC VENT DAMPER68-01862ORDERING INFORMATIONWhen purchasing replacement and modernization products from your TRADELINE® wholesaler or distri

Página 6 - Control with D896

D896 AUTOMATIC VENT DAMPER68-01863NOTE: A minimum of a 30 VA transformer must be usedwhen D896 is installed with S86/S8600/S8610/S8620.Electrical Conn

Página 7 - SETTINGS

D896 AUTOMATIC VENT DAMPER68-01864IMPORTANT1. The atmospheric draft hood outlet area must besmaller or equal to the inlet area of the damperassembly.2

Página 8 - TROUBLESHOOTING

D896 AUTOMATIC VENT DAMPER68-01865Fig. 3. Installing D896 Vent Damper.IMPORTANTNever mount the vent damper with the motoractuator above or below the v

Página 9 - INSTRUCTIONS TO THE HOMEOWNER

D896 AUTOMATIC VENT DAMPER68-01866Fig. 5. D896 with cover off.HoneywellD892/D896WiresHoneywellD80B WiresJohnsonQ35 WiresEFFIKALRVG WiresYellow Orange

Página 10 - ANSI STANDARDS

D896 AUTOMATIC VENT DAMPER68-01867MV MV/PV PVGND(BURNER)24VGND24V SPARKS8600F, H, M; S8610F,HPOWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PRO

Página 11 - D896 AUTOMATIC VENT DAMPER

D896 AUTOMATIC VENT DAMPER68-01868Fig. 10. Snap-Tite™ Box Connector release.CheckoutHeating1. Turn on the power supply.2. If using a thermostat, set t

Página 12

D896 AUTOMATIC VENT DAMPER68-01869Thermostat Setting Symptom Possible Cause ActionSet thermostat 10°Fabove room temperatureto call for heat.No respons

Comentários a estes Manuais

Sem comentários

Honeywell AUTOMATIC VENT DAMPER D896 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Ventiladores Honeywell AUTOMATIC VENT DAMPER D896. Honeywell AUTOMATIC VENT DAMPER D896 User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Ventiladores Honeywell AUTOMATIC VENT DAMPER D896