Honeywell DOLPHIN 99EX Manual do Utilizador

Dolphin™ 99EX Mobile Computerwith Windows® Embedded Handheld 6.5User’s Guide

x

8 - 6Dolphin Wireless ManagerThe Dolphin Wireless Manager provides a centralized interface that enables and disables all the on-board radios. Each rad

8 - 74. When the radio is activated (i.e., transmitting a signal), the OFF button changes to ON.Note: If applicable, information about the radio appea

8 - 8Network CardsThe Network Cards screen allows you to set and configure the type of Network Adapter the Network card in the terminal uses. You can

8 - 9• Select which information types are synchronized, controling how much data is synchronized. For example, you can choose how many weeks of past a

8 - 10Connecting the Dolphin Terminal to the Host WorkstationAfter setting up both the workstation and the terminal:1. Connect the Dolphin terminal to

8 - 11Adding Programs Using ActiveSync or Windows Mobile Device CenterGenerally, software for Windows Embedded Handheld devices must be installed to t

8 - 12• If you copied the file to the \Honeywell\Autoinstall folder, you can perform a Soft Reset (CTRL + ENTER) to install the program. For more info

8 - 13Software UpgradesContact a Honeywell technical support representative for information on available software upgrades for your Dolphin terminal,

8 - 14

9 - 19Working with Wireless Wide Area Networking (WWAN)Overview The 99EX has two options for WWAN connectivity, a data+voice GSM/HSPA+/UMTS/GPRS/EDGE

1 - 11Dolphin 99EX Terminal Agency InformationDolphin 99EX mobile computers meet or exceed the requirements of all applicable standards organizations

9 - 2Signal StrengthThe signal strength of the WWAN connection is indicated by the number of bars that appear in the signal strength icon in the Title

9 - 3SIM Card InstallationShort for Subscriber Information Module, a SIM card stores the subscriber's personal information, GSM/GPRS radio settin

9 - 4Installing a SIM Card1. Press the Power key to put the terminal in Suspend Mode.2. Release the hand strap near the speaker on the back panel of

9 - 5Enabling the WWAN RadioBy default, the WWAN radio is not enabled after a factory reset. Verify the status of the radio in the Dol-phin Wireless M

9 - 6Volume ControlAccessing the Dialer WindowNote: The WWAN radio must be active for voice communication, see Enabling the WWAN Radio on page 9-5.Tap

9 - 7Sending CallsAfter the number is dialed, tap Talk or press the Blue + Send key .Note: The icon indicates that the phone is in use. Ending Cal

9 - 8SecurityThe Security screen provides access to establish or change your security PIN. Check the box next to, “Require a PIN when the phone is use

9 - 9Data Communication (GSM/HSPA+ Global Radio Dolphin Models)You set up data communication via the Connections Manager. The carrier on the SIM card

9 - 103. Enter a name for the connection. Select Cellular Line (GPRS) as the modem. Tap Next.4. Enter the Access point name. Tap Next.5. Enter the use

9 - 116. The connection you just created should appear in the list on the modem tab.7. Tap and hold on the connection. Select Connect on the popup men

1 - 2LED SafetyLED Safety StatementLEDs have been tested and classified as “EXEMPT RISK GROUP” to the Standard: IEC 62471:2006.Infrared LED Safety Sta

9 - 121. When an active SIM card is inserted in the terminal, tap > Settings > Personal > Phone > Menu > Options.2. Select the Network

9 - 13Data Communication GSM/CDMA Dolphin ModelsGobi ManagerThe Gobi Manager enables you to see real time status of the radio, setup your Network sele

9 - 14Establishing Data Communication1. Tap on the Home screen to access the Dolphin Wireless Manager.2. Tap Menu and then select Gobi Settings. 3.

10 - 110Working with the Bluetooth RadioEnabling the Bluetooth RadioYou enable the Bluetooth radio in the Dolphin Wireless Manager (see page 8-6). 1.

10 - 2Pairing and Trusted DevicesThe terminal does support pairing. Pairing happens during general connection setup. Paired devices are "trusted&

10 - 34. Select a device from the list and tap Next. 5. You are prompted to enter a passcode.• If the device has a specific passcode, enter it in the

10 - 48. When the connection is complete, a list of matching and supported services on the device appears. Only the services that are mutually support

10 - 5Transferring Files 1. Tap > File Explorer.2. Navigate to the file you want to transfer.3. Tap and hold on the file and select Beam File on t

10 - 6Making the Terminal DiscoverableBy default, the Dolphin terminal is not discoverable, which means that the terminal will not be found by other B

11 - 111Working with GPSOverviewThe Dolphin 99EX terminal contains an integrated GPS module that allows location tracking of workers and vehicles, pro

1 - 3The equipment is intended for use throughout the European Community; PAN European Frequency Range: 2.402–2.480 GHz. Restrictions for use in Franc

11 - 2GPS Intermediate DriverWhen the first user of GPD1 opens the port, the GPS Intermediate Driver opens the COM7 port. The GPS Intermediate Driver

12 - 112Dolphin 99EX HomeBase DeviceOverviewAs the hub of your Dolphin system, the Dolphin 99EX HomeBase charging and communication cradle supports bo

12 - 2CapacityThe base holds one terminal and features an auxiliary battery well behind the terminal well that can charge a battery pack independently

12 - 3AUX Battery LEDIndicates status of the battery charging in the auxiliary battery well; see Back Panel on page 12-4. For information about char

12 - 4Back Panel Auxiliary Battery Well The base enables you to charge an additional battery pack independently of the terminal well in 4 hours for th

12 - 5Bottom PanelFor details on how to mount the eBase, see Mounting the HomeBase on page 12-9.PowerThe base requires 12 Volts DC input for communica

12 - 6Charging the Main BatteryThe base powers the terminal and fully charges its main battery pack in 4 hours for the standard 3.7V battery or 6 hour

12 - 7CommunicationUSBDolphin terminals support USB communications out of the box.The base also supports USB communications via the USB port located o

12 - 8• If the base is connected to the workstation, the Dolphin terminal automatically opens ActiveSync or the Windows Mobile Device Center to establ

12 - 9Serial ConnectorThe following diagram displays the pin diagram of the serial connector of the base. Note: The signal names are referenced to the

1 - 4Canadian ComplianceThis Class B digital apparatus complies with Canadian ICES-003 and RSS210. Operation is subject to the following two condition

12 - 10

13 - 113Dolphin 99EX eBase DeviceOverviewThe Ethernet Base (eBase) enables a single Dolphin 99EX computer to communicate with a host device over an Et

13 - 2Parts and FunctionsFront PanelTerminal Well Place the terminal in this well to communicate with a host device, power the terminal, and charge th

13 - 3COMM LED The COMM LED indicates the status of data transfer between the Dolphin terminal and the eBase.Ethernet CommunicationUSB CommunicationTh

13 - 4Back Panel Auxiliary Battery WellThe eBase enables you to charge an additional battery pack independently of the terminal well in 4 hours for th

13 - 5DC Power Jack Use the power cable from Honeywell that comes with the eBase to supply power to this power jack. For more information, see Power o

13 - 6Charging the Main BatteryThe eBase provides power to the Dolphin terminal and allows the charging of the terminal’s main battery. The intelligen

13 - 7• The Kernel version must be 26.01 or later in terminals running Windows Embedded Handheld 6.5 Classic. • In terminals running Windows Embedded

13 - 8Setting Up and Connecting the Dolphin Terminal to the eBase1. Verify the base has power. If the Power/Dock LED is not illuminated, see Connectin

14 - 114Dolphin 99EX Mobile Base DeviceOverviewThis charging and communication cradle is designed specifically for in-premise and in-transit data coll

1 - 5For European Community UsersHoneywell complies with Directive 2002/96/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 27 January 2003 on wast

14 - 2Front PanelMounting BracketUsed to mount the base to a fixed location.SpeakerAmplifies the Dolphin’s audio signals.Status LEDIlluminates solid g

14 - 3Bottom PanelThe power supply and RS232 connectors are located on the bottom of the unit.Power Supply ConnectorTo run on vehicle power, you can u

14 - 4Back Panel and Mounting BracketsBall JointsThere are two ball joints: one on the back of the base and one on the mounting bracket. Both ball joi

14 - 5MountingThe adjustable mounting bracket holds the terminal securely in place and gives the user a variety of options for mounting the base.Safet

14 - 6Powering the Dolphin TerminalWhen seated in a base that is connected to the appropriate power source, the Dolphin terminal receives the power to

14 - 7Establishing ActiveSync or Windows Mobile Device Center CommunicationThe Dolphin terminal is usually auto-detected and configured by ActiveSync

14 - 8Serial ConnectorThe following diagram displays the pin diagram of the serial connector of the base. Note: The signal names are referenced to t

15 - 115Dolphin 99EX ChargeBase DeviceOverviewThis 4-slot charging cradle that can power 4 Dolphin terminals, and charge their main batteries in 4 hou

15 - 2Parts and FunctionsFront Panel Terminal WellsThe base contains four terminal wells. Each well has its own dedicated Power/Docking LED and Chargi

15 - 3Back Panel Power Supply ConnectorThis connector receives input from the power adapter. Plug the power connector cable from the power adapter i

1 - 6

15 - 4Charging the Main BatteryThe base provides power to the Dolphin terminals and allows charging of the main batteries in the terminals. The main b

15 - 5Bottom PanelDesk MountingThe DIN Rail (7.5 X 35 mm) slot on the bottom panel enables secure mounting on a horizontal surface.Hardware Required•

15 - 63. Then, using the appropriate nuts and bolts, secure the DIN Rail to a stable, flat horizontal surface. Wall MountingThe optional wall mount br

15 - 72. Slide the bolt through the wall bracket, and thread the toggle nut onto the bolt.3. Press the ends of the toggle nut together, and insert the

15 - 8To secure the base using the optional DIN Rail:Hardware Required• DIN Rail, Qty. 1• 3/16 in. dia x 5/8 in. long pan head screw, Qty. 2• 1/2 in.

15 - 9Channel Bracket Installation (Pre-existing Hardware Installations) When choosing a location and installing the optional channel bracket:• Do not

15 - 102. Attach the channel bracket to a dry, stable surface using the hardware listed on page 15-9 for the appropriate mounting surface.Mounting int

16 - 116Dolphin 99EX Net Base DeviceOverviewThe Net Base enables up to four Dolphin 99EX mobile computers to communicate with a host device over an Et

16 - 2Parts and FunctionsFront PanelTerminal Wells The Net Base contains four terminal wells. Each well has its own dedicated Power/Dock LED and COMM

16 - 3Back Panel DC Power Jack Use the power cable from Honeywell that comes with the Net Base to supply power to this power jack. For more informatio

2 - 12Getting StartedOut of the BoxVerify that the carton contains the following items: • Dolphin 99EX mobile computer (the terminal)• Main battery pa

16 - 4Bottom PanelFor details on how to mount the Net Base, see Mounting the Net Base on page 16-6.PowerThe terminal requires 12 Volts DC input for co

16 - 5Charging the Main BatteryThe base provides power to the Dolphin terminals and allows the charging of the main batteries in the terminals. The ma

16 - 62. Plug the CAT-5 Ethernet cable into one of the RJ45 connectors on the back of the Net Base.3. Plug the Ethernet cable into the network. 4. Ins

16 - 7Bottom PanelDesk MountingThe DIN Rail (7.5 X 35 mm) slot on the bottom panel enables secure mounting on a horizontal surface.Hardware Required•

16 - 83. Then, using the appropriate nuts and bolts, secure the DIN Rail to a stable, flat horizontal surface. Wall MountingThe optional wall mount br

16 - 92. Slide the bolt through the wall bracket, and thread the toggle nut onto the bolt.3. Press the ends of the toggle nut together, and insert the

16 - 10To secure the base using the optional DIN Rail:Hardware Required• DIN Rail, Qty. 1• 3/16 in. dia x 5/8 in. long pan head screw, Qty. 2• 1/2 in.

16 - 11Channel Bracket Installation (Pre-existing Hardware Installations) When choosing a location and installing the optional channel bracket:• Do no

16 - 122. Attach the channel bracket to a dry, stable surface using the hardware listed on page 16-11 for the appropriate mounting surface.Mounting in

17 - 117Dolphin 99EX QuadCharger DeviceOverviewThis 4-slot charging station provides intelligent battery management for the rechargable battery packs

2 - 2Before Initial UseTerminals are shipped with both batteries discharged of all power. The initial charging time for the main battery pack is 4 hou

17 - 2Parts and FunctionsTop Panel Charging SlotsThere are 4 charging slots. Each slot holds one Li-ion or Li-poly battery and charges it independentl

17 - 3Supplying PowerThe charger must be connected to a power source via the Honeywell power adapter cable so that volt-age is adjusted appropriately.

17 - 4Mounting the QuadChargerThe charger should be on a dry, stable surface and can be mounted on a flat, horizontal surface such as a desktop or wor

17 - 5TroubleshootingIf you encounter problems with your QuadCharger device, refer to chart below for possible solutions. If problems persist, please

17 - 6

18 - 118Customer SupportProduct Service and RepairHoneywell International Inc. provides service for all its products through service centers throughou

18 - 2For ongoing and future product quality improvement initiatives, the 99EX comes equipped with an embedded device lifetime counter function. Honey

18 - 3Limited WarrantyHoneywell International Inc. ("HII") warrants its products and optional accessories to be free from defects in materia

18 - 4How to Extend Your WarrantyHoneywell International Inc. offers a variety of service plans on our hardware products. These agreements offer conti

2 - 3The Clock Settings screen appears.Tap the arrow to the right of the time zone to open the drop down menu. Select the appropiate time zone from t

Honeywell Scanning & Mobility9680 Old Bailes RoadFort Mill, SC 29707www.honeywellaidc.com99EX-UG Rev A3/11

DisclaimerHoneywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document w

2 - 4Home ScreenAfter the Dolphin terminal initializes the first time, you see the Home screen. Tap to reach the Start screen from the home screen.

2 - 5New text messageNew voicemailNew instant messageVibrate onRinger offSpeakerphone onVoice call in progressCalls are forwardedCall on holdMissed ca

2 - 6No active network connectionGPRS availableGPRS connectingGPRS in use HSDPA availableHSDPA connectingHSDPA in useEDGE availableEDGE connectingEDGE

2 - 7Horizontal ScrollThe Horizontal Scroll, located at the top of most application windows, provides access to additional application screens. You ca

2 - 8File ExplorerYou can also use the File Explorer to find files and organize these files into folders.1. Tap > File Explorer .2. Tap the Up b

2 - 9File Provisioning on the 99EX\IPSM\HoneywellThe IPSM folder is the only partition on the 99EX that persists across a kernel upgrade (*.UPG file e

2 - 10Resetting the TerminalThere are three types of system resets: a soft reset, a hard reset, or a factory reset. The soft and hard resets preserve

3 - 13Hardware OverviewStandard Configurations for the 99EXWLAN & WPAN• Microsoft Windows Embedded Handheld 6.5 Classic• OMAP3715 (1Ghz)• 256MB RA

3 - 2Some configurations of the 99EX terminal are available with an external housing made of plastic that is specifically designed for the healthcare

3 - 3Peripherals for the 99EXEach of the following items is sold separately to enhance the capabilities of your Dolphin terminal. Dolphin 99EX HomeBas

iiiChapter 1 - Dolphin 99EX Terminal Agency InformationLaser Safety...

3 - 4Accessories for the 99EXEach of the following items is sold separately to enhance your terminal’s capabilities.Note: When using accessories where

3 - 5Battery Pack The rechargable battery pack (i.e., standard 3.7V, 3060mA Li-poly or extended 3.7V, 5000mA Li-ion) provides the main power for the t

3 - 6Front Panel Features for the 99EXBlue Modifier KeySee Using the Modifier Keys on page 6-3.Front SpeakerThe front speaker is the receiver for hand

3 - 7Touch Panel DisplayThe color 3.7 inch liquid crystal display (LCD) touch panel is covered with an industrial, protective lens for greater durabil

3 - 8Back Panel Features for the 99EXBattery DoorThe battery door secures the Li-ion or Li-poly battery pack in the terminal’s battery well. For infor

3 - 9Stylus SlotThe stylus is used to operate the touch panel. The back panel of the terminal features a storage slot to hold the stylus when not in u

3 - 10Right Side Right ButtonBy default, the Right Button triggers the scanner/imager. You can reassign the button to launch applications or execute c

3 - 11Bottom Panel: 99EXNote: Signals referenced are for a DTE device.I/O ConnectorThe I/O connector powers the terminal, charges the main battery, an

3 - 12Using the Touch Panel Honeywell defines proper use of the terminal touch panel as using a screen protector and proper stylus. Screen protectors

3 - 13• Isopropyl Alcohol wipes (70%)• CaviWipes™•Virex® 256•409® Glass and Surface Cleaner•Windex® Blue• Gentle dish soap and waterBatteriesThere are

ivBack Panel: 99EX ...3-7Back Panel Featu

3 - 14Battery Error NotificationIf your terminal displays the following indicators, replace the main battery pack with a Honeywell Li-poly or Li-ion b

3 - 15If at any time the backup battery becomes fully discharged of power (e.g., the terminal is left without the main battery pack for more than 30 m

3 - 16LowState=10%This sets the Critical Battery point to 10%. When the battery hits the percentage charge specified here, the user is notified.Note:

3 - 17Installing a Memory Card1. Press the Power key to put the terminal in Suspend Mode.2. Release the hand strap hook near the speaker on the back

3 - 18

4 - 14Using the Scan Image EngineOverviewThe Dolphin terminal houses a compact image engine that instantly reads popular 1D and 2D bar codes and suppo

4 - 2Depth of FieldThe depth of field measurements used the following parameters:• Distances are measured from the front of the engine.• +23°C (+73°F)

4 - 3Supported Bar Code Symbologies 10 mil QR 3.3 (8.4)5.0 (12.7)1.7 (4.3)2.2 (5.6)7.1 (18.0)4.9 (12.4)4.3 (10.9)10.6 (26.9)6.5 (16.5)20 mil QR 2.2 (5

4 - 4DecodingThe terminal supports two types of image decoding for use in various bar code reading and imaging applications: full-area imaging and Adv

4 - 5N5603 Red High-Vis Aiming PatternIf your Dolphin terminal is configured with a 5603 imager, high-vis aimers frame the bar code for more intuitive

v34-Key Alpha/Numeric Keyboard ... 6-5ALPHA Key...

4 - 6Capturing ImagesThe image-capture process is an intuitive, split-second operation for experienced users. By following the basic guidelines, new u

4 - 77. Unless otherwise specified by the application in use, the image is saved to the \My Device\My Documents folder. Enabling the AimerYou can enab

4 - 8

5 - 15Using the Color CameraOverviewDolphin 99EX terminals equipped with a 3.1-Megapixels Resolution color camera with Automated Cam-era Control (ACC)

5 - 2OptionsTap Options > Camera.The Camera Options menu appears. There are five tabs of configurable options accessible from the Camera Options

5 - 3MenuTap Menu on the Command Bar to adjust the camera settings, switch to video mode, and access addi-tional camera options.OptionsTap Menu >

5 - 4

6 - 16Using the KeyboardsAvailable KeyboardsThere are four keyboard options in the 99EX series:All Keyboards Contain the Following:• Backlit for easy

6 - 2Using the Function KeysName Key FunctionBacklight Turns the keyboard backlight on and off. Flashlight & Turns the flashlight on and off. The

6 - 3Using the Modifier Keys Using the Navigation KeysLocated in the center of each keyboard for easy access with either hand, the navigation keys nav

viDolphin Wireless Manager ... 8-6Dolphin Wireless Man

6 - 4Note: Additional functionality varies according to the application in use. & Moves the cursor down one page.Moves the cursor one character to

6 - 534-Key Alpha/Numeric KeyboardALPHA Key The ALPHA lock key enables you to toggle between the alpha and numeric keyboard modes. On the 34-Key Keybo

6 - 634-Key Alpha/Numeric Keyboard CombinationsKey NUM (Default)Shift-NUM ALPHA Shift-ALPHABlue Red ESC EscapeLeft Left Left Left Left Send (Phone)Lef

6 - 7F1 F1 F1 F1 F1 + F5F2 F2 F2 F2 F2 - F6F3 F3 F3 F3 F3 / F7F4 F4 F4 F4 F4 \ F8SFT Shift Shift Shift ShiftSP Space Space Space Space ; SpaceBKSP Bac

6 - 834-Key Numeric (Calculator) KeyboardALPHA Key The ALPHA lock key enables you to toggle between the alpha and numeric keyboard modes. On the 34-Ke

6 - 934-Key Numeric (Calculator) Keyboard CombinationsKey NUM (Default)Shift-NUM ALPHA Shift-ALPHABlue Red ESC EscapeLeft Left Left Left Left Send (Ph

6 - 10F1 F1 F1 F1 F1 + F5F2 F2 F2 F2 F2 - F6F3 F3 F3 F3 F3 / F7F4 F4 F4 F4 F4 \ F8SFT Shift Shift Shift ShiftSP Space Space Space Space ; SpaceBKSP Ba

6 - 1143-Key Alpha/Numeric KeyboardNumber Lock (NUM) Key The Number Lock key enables you to toggle between the alpha and numeric keyboard modes. On th

6 - 1243-Key Keyboard CombinationsKey ALPHA (Default)Shift-ALPHA NUM Shift-NUM Blue RedESC EscapeLeft Left Left Left Left Send (Phone)LeftScan ScanRig

6 - 13L l L 7& F12M m M 8 * (multiply) F13N n N 9( F14O o O F15P p P =F16Q q Q . (period) > * (multiply) F17R r R 0) F18S s S , (comma) < #

viiChapter 11 - Working with GPSOverview...

6 - 1455-Key Full Alpha/Numeric Keyboard55-Key Keyboard CombinationsKey Normal Shift Blue RedESC EscapeLeft Left Left Send(Phone)LeftScan ScanRight Ri

6 - 15Backlight Toggle Keyboard Backlight On/Off Toggle Flashlight On/OffToggle Keyboard Backlight On/OffTAB Ta bUp Up Up Volume Up PriorDown Down Dow

6 - 16D d D )F4E e E =F5F f F !F6G g G @F7H h H $F8I i I &F9J j J _ (underscore) F10K k K ?F11L l L \F12M m M /F13N n N ~F14O o O 'F15P p P;

6 - 17Red RedZ z Z z or Z z or ZKey Normal Shift Blue Red

6 - 18

7 - 17System SettingsOverviewCustomized settings are available on the System Settings menu. Tap > Settings and the settings screen opens. Icon De

7 - 2Clock & AlarmsThe Clock & Alarms settings can be accessed from the Home screen or the Settings Menu.1. On the Home screen, tap the line t

7 - 3Personal MenuTo access the Personal Menu, tap > Settings > Personal. The screen opens displaying the Per-sonal Menu.ButtonsThe Buttons se

7 - 4Changing Button Assignments1. After HotKeys is enabled, tap > Settings > Personal > Buttons . Note: The buttons that appear on this

7 - 5Using File ExplorerIf you do not see the program listed, you can either use File Explorer to move the program or ActiveSync on the workstation to

viiiMounting the eBase... 13-8Desk Mounting..

7 - 63. Navigate to the Windows folder and open the Start Menu (My Device > Windows > Start Menu > Programs), tap and hold a blank area of th

7 - 7System MenuThe System menu enables you to verify and sometimes alter system parameters. To access the System menu, go to Start > Settings >

7 - 8AboutThe About system setting displays specific information about the terminal. It contains three screens:Version Screen Displays the information

7 - 9Copyrights Screen Displays important copyright information.BacklightThe Backlight system setting enables you to customize backlight functionality

7 - 10BatteryThe Battery system settings menu contains two tabs: Battery Status and Log Config. The Battery Sta-tus tab provides the status of the mai

7 - 11EncryptionEncryption gives you the option of encrypting files placed on storage cards so that those files cannot be read by any other device.Err

7 - 12Five Volt ControlFive Volt Control gives you the option to manually enable 5V output to supply power to an external device. By default, 5-Volt O

7 - 13Event Track displays an event log summary of detected free fall events exceeding 2 ft. over 250 ms. The summary includes the time, date, and dur

7 - 14Managed ProgramsManaged Programs are a list of programs that are managed if enrolled to enterprise domain. Managed Programs is the client-side t

7 - 15MemoryThe Memory applet shows the capacity and usage of the Storage and Program portions of the Flash file system. The Storage portion includes

ixChapter 17 - Dolphin 99EX QuadCharger DeviceOverview...

7 - 16RILThe RIL Information screen displays useful statistics for the GSM WAN Voice module (PH8).To verify whether or not the GSM radio is enabled, c

7 - 17The terminal is loaded with a number of pre-programmed regional settings. Select one from the list and the results appear on the screen. To see

7 - 18ScreenThe Screen system setting contains three screens: General, Clear Type, and Text Size.General ScreenOrientationThe General screen enables y

7 - 19Task ManagerThe Task Manager provides information about applications and processes running on your mobile com-puter. You can use the Task Manage

7 - 20Using the Task ManagerApplications To view the status of the programs running on your mobile computer, tap the Menu button at the bottom of the

8 - 18CommunicationConnections MenuThe Connections system setting provides access to the terminal’s various wireless communication options. Note: A

8 - 2Using the IrDA PortUsing the IrDA port, you can send and receive data between the terminal and other devices equipped with infrared. This can inc

8 - 35. When the IrDA port finds the aligned IrDA port, it immediately starts sending the selected file. The selected device reads “Sending.”6. When t

8 - 4Connections ManagerMicrosoft’s Connections Manager sets up multiple network connections to Internet Service Providers (ISPs) via external modem.D

8 - 5• Proxy server connectionNote: If you are connected to your ISP or private network during synchronization, the terminal should download the prope