Honeywell T8611G Manual do Utilizador descarregar pdf

® U.S. Registered Trademark

INSTALLATION INSTRUCTIONS

69-1406-1

T8611G Chronotherm

Deluxe Programmable

Heat Pump Thermostats

APPLICATION

The T8611G Chronotherm® IV Deluxe Programmable

Heat Pump Thermostats provides electronic control of 24

Vac single-zone heat pump systems.

Refer to Table 1 for a general description of the

thermostat. All T8611 thermostats require a common wire

to supply power.

Table 1. Description of T8611 Thermostats.

MERCURY NOTICE

If this control is replacing a control that contains

mercury in a sealed tube, do not place your old

control in the trash. Dispose of properly.

Contact your local waste management authority

for instructions regarding recycling and the

proper disposal of the old control.

INSTALLATION

When Installing this Product...

1. Read these instructions carefully. Failure to follow

the instructions can damage the product or cause

a hazardous condition.

2. Check the ratings given in the instructions and on

the product to make sure the product is suitable for

your application.

3. Installer must be a trained, experienced service

technician.

4. After completing installation, use these instructions

to check out the product operation.

Location

Install the thermostat about 5 ft (1.5m) above the floor in

an area with good air circulation at average temperature.

See Fig. 1.

Do not install the thermostat where it can be affected by:

— drafts, or dead spots behind doors and in corners.

— hot or cold air from ducts.

— radiant heat from sun or appliances.

— concealed pipes and chimneys.

— unheated (uncooled) areas such as an outside wall

behind the thermostat.

Wallplate Installation

The thermostat can be mounted horizontally on the wall

or on a 2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.

Position wallplate horizontally on the wall or on a

2 in. x 4 in. (50.8 mm x 101.6 mm) wiring box.

1. Position and level the wallplate (for appearance

only). The thermostat will function correctly even

when not level.

2. Use a pencil to mark the mounting holes. See Fig.

3. Remove the wallplate from the wall and drill two

3/16 inch (76 mm) holes in the wall (if drywall) as

marked. For firmer material such as plaster, drill

two 7/32 inch (5.56 mm) holes. Gently tap anchors

(provided) into the drilled holes until flush with the

wall.

4. Position the wallplate over the holes, pulling wires

through the wiring opening.

5. Loosely insert the mounting screws into the holes.

6. Tighten mounting screws.

T8611 Changeover System Selection Fan Selection Comments

G Automatic Em Heat-Heat-Off-Cool-Auto On-Auto System and fan selections are done by keyboard.

1 2 3 4 5 6 ... 11 12

Resumo do Conteúdo

Página 1 - Heat Pump Thermostats

Página 2 - Mounting Thermostat

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS69-1406—1 10TROUBLESHOOTING GUIDETable 6. Troubleshooting Guide.Symptom Possible Cause

Página 3 - SETTINGS

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS11 69-1406—1System on indicator (flame=heat, snowflake=cool) is displayed, but no warm

Página 4 - INSTALLER SETUP

69-1406—1 G.H. Rev. 12-02 www.honeywell.com/yourhomeT8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATSAutomation and Control Soluti

Página 5 - 5 69-1406—1

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS69-1406—1 2Fig. 1. Typical location of thermostat.Fig. 2. Mounting the wallplate.WIRI

Página 6 - 69-1406—1 6

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS3 69-1406—1Using Thermostat Keys (Fig. 6)The thermostat keys are used to:• set current

Página 7 - INSTALLER SYSTEM-TEST

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS69-1406—1 4Temperature SettingsRefer to Table 2 for the default program. If the daytim

Página 8 - 69-1406—1 8

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS5 69-1406—1Adaptive Intelligent Recovery™ control.13 0 Adaptive Intelligent Recovery™

Página 9 - CHECKOUT

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS69-1406—1 6IMPORTANTReview the settings to confirm that they match the system. Press R

Página 10 - TROUBLESHOOTING GUIDE

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS7 69-1406—1Setting Current Day and Time1. Press Set Current Day/Time.NOTE: On initial

Página 11 - 11 69-1406—1

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS69-1406—1 8Table 5. Installer System Test Options.NOTE: Press any key and the displaye

Página 12 - T8611G CHRONOTHERM

T8611G CHRONOTHERM® IV DELUXE PROGRAMMABLE HEAT PUMP THERMOSTATS9 69-1406—1THERMOSTAT INFORMATION1. Press the Time ∆ key to access the thermostat info

Comentários a estes Manuais

Sem comentários

Honeywell T8611G Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Termóestatos Honeywell T8611G. Honeywell T8611G User's Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Termóestatos Honeywell T8611G