Honeywell FocusBT AP-010-BT Manual do Utilizador

AP-010-BT and AP-100-BT Access Point Device with Bluetooth® Wireless Technology Installation Guide

www.metrologic.com 6 INSTALLATION USB Host Connections 1. Turn off power to the host system. 2. Plug the USB connector into the to a dedicated US

7ESTABLISHING COMMUNICATION Between the Scanner and the Access Point Device To establish communication between the scanner and access point device

www.metrologic.com 8 ACCESS POINT DEVICE OPERATION Page/Disconnect Button The access point has a button located on the top of the device that can

9CONFIGURATION PROCEDURES The following information is for replacement applications or situations requiring scanner reconfiguration. Some of the c

www.metrologic.com 10 CONFIGURATION PROCEDURES CodeXML Protocol Compatibility The CodeXML protocol does not support page/disconnect button functio

11CONFIGURATION PROCEDURES Access Point Device Configuration in CodeXML Mode When a scanner is using the CodeXML protocol all configuration data i

www.metrologic.com 12 CONFIGURATION PROCEDURES Optional Configuration Bar Codes The following bar codes are for reference only. Suffix Characters Di

13CONFIGURATION PROCEDURES The following bar codes require an established communication link between the access point device and a scanner using

www.metrologic.com 14 CONFIGURATION PROCEDURES Country/Scan Code Table Selects * Enable USA Keyboard ³416260 Enable Swiss Keyboard ³416280 Enable S

15UPLOADING AND DOWNLOADING SETTINGS Uploading Settings via MetroSet2 The upload† feature in MetroSet2 allows the user to retrieve the current s

Copyright © 2008 Metrologic Instruments Inc. All rights reserved. No part of this work may be reproduced, transmitted, or

www.metrologic.com 16 UPLOADING AND DOWNLOADING SETTINGS Downloading Settings via MetroSet2 The download† feature in MetroSet2 allows the user to d

17UPGRADING THE FIRMWARE Upgrading the Firmware in the Access Point Device The access point device is part of Metrologic's product series with

www.metrologic.com 18 UPGRADING THE FIRMWARE Upgrading FocusBT Firmware via the Access Point Device With MetroSet2, scanner firmware upgrades can be

19DESIGN SPECIFICATIONS Access Point Device OPERATIONAL System Interfaces: RS232, Keyboard Wedge, RS485S, USB S Applicable for IBM® Host applica

www.metrologic.com 20 DEVICE AND CABLE TERMINATIONS The access point device terminates to a single 10-Pin RJ45, Female Socket. The following charts

21DEVICE AND CABLE TERMINATIONS Cable Pinout Connections RS232 PowerLink Cable MLPN 55-55500 Pin Function 1 Shield Ground 2 CTS 3 RXD 4 Reserve

www.metrologic.com 22 DEVICE AND CABLE TERMINATIONS Cable Pinout Connections Keyboard Wedge Cable MLPN 55-55502 Pin Function 1 Keyboard Clock 2

23REGULATORY COMPLIANCE EMC Emissions FCC Part 15, ICES-003, CISPR 22, EN 55022, EN300 328 V1.6.1, EN310 489-17 V1.2.1 Immunity CISPR 24, EN 5

www.metrologic.com 24 REGULATORY COMPLIANCE Changes or modifications not expressly approved by the party responsible for compliance could void the

25LIMITED WARRANTY The AP-010-BT and AP-100-BT access point devices are manufactured by Metrologic at its Suzhou, China facility. The AP-010-BT

iiTABLE OF CONTENTS Introduction Product Overview ... 1 B

www.metrologic.com 26 INDEX A AC ...see power Accessories ... 2 Address Bar Code ...

70-79035A October 2008 Printed in China © 2008 Honeywell International Inc.

iiiTABLE OF CONTENTS Uploading and Downloading Settings Uploading Settings via MetroSet2 ...

1INTRODUCTION Honeywell’s access point devices with Bluetooth® wireless technology provide customers with a flexible and convenient solution for

www.metrologic.com 2 INTRODUCTION OPTIONAL ACCESSORIES Part # Description 55-55500-3 RS232 Straight PowerLink Cable, Black 55-55502-N-3 Keyboard

3INTRODUCTION Mounting Specifications 1. Drill two, 1.6 mm pilot holes in the mounting surface. The pilot holes should be located on a common c

www.metrologic.com 4 INTRODUCTION Product Labels The serial number label located on the bottom of the access point device provides important inform

5INSTALLATION Cable to Access Point Connection 1. Align the tab on the modular connector with the pinhole on the access point device (see figure