Honeywell Scanner MS9520 Manual do Utilizador Página 103
- Página / 116
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
22–1
IS4823 and IS4825 Scan Engines
Operating Modes
Activation Modes
³ 4 1 8 3 0 4
* Activate Scanning with the External Trigger –
An external I/O pin is used to enable the scanning
cycle. A High-to-Low transition on the I/O signal is
used to activate scanning. The signal must be
deactivated (HIGH) and re-activated for
subsequent scanning cycles. The scanning cycle
is terminated based on the default period of time
(2 seconds), a variable period of time, when the
I/O signal is deactivated (Low-to-High), or when a
bar code is scanned and transmitted.
³ 1 1 8 1 1 0
Activate Scanning on Receipt of the <DC2>
Character – A received <DC2> character initiates
the scanning cycle. The scanning cycle is
terminated based on the default period of time
(2 seconds), variable laser timeout selected, or
when a bar code is scanned and transmitted.
³ 1 2 0 3 1 6
Activate Scanning Using D/E – A received ‘E’
character initiates the scanning cycle. The
scanning cycle is terminated based on the default
period of time (2 seconds), variable laser timeout
selected, or receipt of a ‘D’ or when a bar code is
scanned and transmitted.
³ 1 1 7 4 1 5
Activate Scanning with Address – A
configurable address character is used to initiate
scanning. T
he scanning cycle is terminated based
on the default period of time (2 seconds), variable
laser timeout selected, or when a bar code is
scanned and transmitted.
³ 9 1 7 5 0 0
~ Address Value – Use this bar code with a code
byte sequence (on page 16–1) that represents
the desired character to be used to initiate
scanning. An ASCII reference table is available
on page 16–3.
22
- MetroSelect 1
- Disclaimer 2
- Trademarks 2
- Table of Contents 3
- Prefixes/Suffixes 4
- Code Formatting 4
- Introduction 7
- Need To Start Over? 8
- Code Types and Decode Rules 9
- Code 128 10
- Code 39 10
- ³ 1 0 0 2 0 5 11
- ³ 1 0 0 7 1 2 11
- ³ 1 0 7 7 0 5 11
- 2 OF 5 CODES 12
- ³ 1 0 0 1 1 0 13
- ³ 1 0 0 5 0 7 13
- Codabar 14
- Code 93 14
- Code 11 14
- Telepen 15
- Plessey Codes 15
- Additional Decode Features 16
- Configurable Code Lengths 17
- ³ 9 0 2 6 0 0 18
- ³ 9 0 3 2 0 0 18
- Supplements 19
- ³ 1 0 1 4 0 3 20
- ³ 1 0 1 2 0 5 20
- ³ 1 0 1 0 0 1 21
- ³ 1 0 1 3 1 5 22
- ³ 1 2 5 1 1 5 22
- ³ 1 0 1 2 1 0 23
- ³ 1 0 1 2 0 0 23
- ³ 1 2 5 0 1 7 23
- ³ 1 2 5 0 0 7 23
- GS1 DataBar 25
- GS1 DataBar Limited 26
- GS1 DataBar Expanded 26
- ISBT Code 128 Implementation 27
- ³ 3 0 1 3 6 0 28
- ³ 1 3 8 4 0 3 28
- ³ 4 3 8 4 1 2 0 29
- ³ 4 3 8 4 1 3 0 29
- ³ 4 3 8 4 1 4 0 29
- ³ 9 3 8 1 0 0 29
- ³ 9 3 8 3 0 0 29
- Communications 31
- Scanner Operation 33
- Redundant Scans 34
- Same Symbol Time Outs 35
- LED Options 35
- Beeper Options 36
- ³ 1 1 6 9 1 3 37
- ³ 1 2 5 0 1 0 37
- Data Transmission Delays 38
- ³ 1 1 8 4 1 2 39
- ³ 8 1 9 1 2 0 0 39
- Host Scanner Commands 40
- ³ 1 1 5 9 0 6 41
- ³ 1 1 8 2 1 3 41
- Test Modes 42
- ³ 1 0 5 5 0 7 44
- ³ 9 0 6 1 0 0 44
- ³ 9 0 6 5 0 0 45
- ³ 1 2 4 7 1 6 45
- Standard Prefix Characters 46
- ³ 1 0 5 5 1 1 47
- ³ 1 1 6 1 1 1 47
- Standard Suffix Characters 48
- Block Check Character 49
- Character Replacements 50
- ³ 9 0 4 9 0 0 51
- ³ 9 9 9 9 8 4 51
- Special Formats 52
- ³ 1 0 7 5 0 2 54
- ³ 1 0 7 6 0 0 54
- Codabar Formatting 55
- Code 39 Formatting 56
- Code 11 Formatting 56
- Plessey 57
- 2 of 5 Code Formatting 57
- Parity Features 59
- Baud Rate 59
- Data/Stop Bits 60
- Hardware Handshaking 60
- ³ 1 1 5 8 0 5 61
- ³ 1 2 4 5 0 2 61
- ³ 1 2 4 5 1 3 61
- ³ 1 1 5 8 0 7 61
- Software Handshaking 62
- Miscellaneous 63
- Keyboard 65
- Keyboard/System Type 66
- ‘Dumb’ Terminal Selections 67
- Special Keyboard Features 68
- ³ 1 1 6 2 1 4 69
- ³ 1 1 6 3 1 6 69
- ³ 1 1 6 3 0 6 69
- ³ 1 1 6 4 0 0 69
- ³ 1 1 6 3 0 4 69
- InterScan Code Delays 70
- Control Sets 71
- ³ 9 9 9 9 9 3 73
- Light Pen Parameters 75
- Set Narrow Element Width 76
- 46xx Configuration 77
- ³ 9 9 9 9 7 8 79
- ³ 9 9 9 9 7 2 80
- Code Bytes Usage 81
- Reserved Codes 82
- Code Type Table 82
- ASCII Reference Table 83
- MS9520 Voyager 89
- MS9540 VoyagerCG 89
- Series 89
- Laser/Scan Modes 90
- ³ 9 9 9 9 7 9 92
- ³ 1 1 7 0 1 0 92
- ³ 1 1 7 0 0 1 92
- ³ 1 1 7 0 1 1 92
- MS9524 and MS9544 93
- VoyagerPDF 93
- ³ 1 1 5 0 1 5 94
- ³ 1 1 5 0 1 3 94
- MS9535 VoyagerBT 95
- ³ 1 2 3 7 0 2 96
- ³ 1 2 3 7 1 2 96
- MS9535-5M VoyagerBT 97
- ³ 1 2 5 6 1 2 98
- ³ 1 2 3 9 1 5 98
- ³ 1 2 0 3 0 5 101
- ³ 8 4 6 6 0 1 1 0 101
- Operating Modes 103
- Activation Mode Features 104
- Continuous Blinky Mode 105
- Sleep Mode 105
- Miscellaneous Features 107
- Serial Program Mode 108
- Customer Support 109
- Product Service and Repair 110
Manuais e produtos relacionados com Leitores de códigos de barras Honeywell Scanner MS9520
(32 páginas)
(188 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais